Knowledge base · Service
Hot tub fault: what you see yourself, and what you may expect from service
Most messages on a hot tub panel are about too little water flow or water that is too hot. That is where you start at home, with the water level, the filter and the cover. If that does not solve it, you may expect something concrete from after-sales: someone who answers the phone, a reply within 24 hours, a diagnosis before anything is ordered and a quote before anything is replaced.
Loading photoThe answer
Six things you may expect from after-sales
Not a favour, a normal part of the purchase.
A spa is machinery in the garden: a pump, a heater, a control system and water that stays at temperature day and night. Somewhere in the years it stands there, something may falter. What matters is what happens next.
Reachability
Someone who answers
A number where a person picks up who knows the spa. You can reach us on 085 070 41 71. We have no central helpline.
Response
A reply within 24 hours
We respond to service requests within 24 hours.
Diagnosis
Diagnosing the fault
A diagnosis starts with questions: what is on the panel, what do you hear, since when. Sometimes that settles it, with a setting or a reset. If not, someone comes out to measure before a part is ordered.
Parts and quote
In writing before the repair
Labour, original parts and lead time on paper, and work starts only after your agreement. That way you know in advance what a repair outside warranty costs.
Warranty
The dealer settles it with the factory
If the defect is covered by the manufacturer’s warranty, you should not have to call the manufacturer yourself. Whoever installed the spa handles the claim and keeps you informed.
File
Knowing what is there
Serial number, water reading, a photo of the base. If that was recorded at installation, you have nothing to explain when a fault comes up. We have your file to hand the moment you call.
Fault codes
What the most common messages mean
According to the Balboa user guide for the TP600 and TP400 panels (document 40940, 2019).
The control systems we supply are made by Balboa and Gecko. Balboa describes in the user guide for the TP600 and TP400 panels (document 40940, 2019) what each message means. Older Balboa panels show shorter codes with the same meaning, such as FLO and Sn. A Gecko panel words its messages differently. The route is the same: check yourself first, then call.
HFL or LF: too little water through the heater
The control system measures too little flow past the heating element. With HFL the heater tries again after about a minute. With LF it switches off until you press a button. Check yourself first: water level, filter, valves open, not too many jets closed. If the message comes back after that, call.
dr: the heater may be running dry
There is too little water in the heater to start it safely. The spa shuts down for fifteen minutes. After that you restart it by pressing any button. Look at the water level and the filter first. If the message returns, call. A heater that is close to running dry is not something you keep resetting.
OHS or OHH: the water or the heater is too hot
With OHS a sensor has measured water at 43.3 °C and the control system halts the spa functions until the water drops below 42.2 °C. With OHH it is the heater itself that became too hot (47.8 °C) and the spa shuts down. Check whether a pump has run for a long time and whether it is very warm outside. If the temperature does not drop by itself, or the message keeps coming back, call.
Sensor messages: the temperature sensors disagree
The control system works with two temperature sensors. If they drift apart or one fails, the panel says so. Balboa is brief here: call for service. There is little to check yourself. This is a visit.
Priming Mode and freeze protection: not faults
After every power interruption the panel starts in Priming Mode for four to five minutes so the pumps can purge air. The heater stays off meanwhile. And in cold weather pumps may start by themselves: that is the freeze protection, not a defect.
Do it yourself, or leave it
What you check yourself, and what you leave alone
Four things you check at home before you call.
- Water level. If the water is too low, the pump draws in air and you get a flow message. Top up to the level you were shown at installation.
- Filter. Take the filter out and rinse it. A clogged filter restricts the intake and produces exactly the messages above. If in doubt, put in a clean spare.
- Cover and heat. Is the cover properly closed? On a hot day, or after a pump has run for a long time, the water can rise above the set temperature. That is the OHS message above.
- Reset with a button. Messages such as LF, dr and OHH are reset with any button on the panel, once you have checked the water level and the filter. You need not touch anything beyond that button.
What you leave alone: the cabinet, the connection box and the residual current device. Work on the electrics is work for the engineer or a certified electrician. And on the message that a pump appears to be stuck on, Balboa is clear: switch the spa off, do not enter the water, and call.
Points to consider
What warranty does not cover, and what cannot be done remotely
Two things we would rather say beforehand than afterwards.
The manufacturer’s warranty on the Sunspa lines runs from the installation date: five years on the shell, two years on the cabinet, plumbing, pumps, control system and jets, one year on the heater. Bullfrog specifies per component and per series. We go through those terms with you at the quote. A repair by a non-authorised party or with non-original parts voids the warranty. The Bullfrog warranty applies to the first owner in private use, and after the first six months transport and installation costs may be for your account.
Please note: a Wellness plan is not an extended warranty. With all three plans you pay no call-out fee on a fault. With Elite the labour is included too, but a complete pump or a new shell falls outside it even then. If it comes to that, there is a quote first.
The second thing: a fault is rarely solved over the phone, and we do not read your spa remotely. What we do have is your file: which model, which control system, what the water did at the last service. That is why, on the phone, we often already know roughly where to look.
In practice
How a fault runs with us
Call, diagnosis, quote, repair. Maintenance also for a spa you bought elsewhere.
You call 085 070 41 71 and get us on the line, or you are called back within 24 hours. Sometimes a setting or a reset is all it takes. If not, we come out to run diagnostics and take measurements, anywhere in the Netherlands.
If something needs replacing, there is a written quote first: labour, parts and lead time. We start after your agreement. If the defect is covered by warranty, we sort that out with the manufacturer. With a spa we installed, the engineer who comes is the one who put it in.
With a Wellness plan you pay no call-out fee on a fault. With Elite the labour is included too. A spa you bought elsewhere we take into maintenance just the same. For a sauna the route is the same. There the work is mostly in the heater and the control system, equipment we know from our own installations.
To have at hand when you call
The message on the panel, word for word (a photo helps), the water level, when the filter was last cleaned and whether the spa has just had a power cut. For a spa we installed, we already have the serial number. For another spa, please have the type plate ready.
Further reading
Related articles
Maintenance and service
The three Wellness plans, the single annual service and the four steps of a repair.
Warranty and aftercare
The terms per component, and who handles your claim.
Cloudy or foaming spa water
What the water tells you before the machinery does, and what really helps.
Accountability
Source and author
The fault codes come from the manufacturer’s user guide. The procedure is how we carry it out.
A fault?
Report your fault to Carlo or Max
We answer your call or call back within 24 hours. You receive a quotation before parts are replaced.

